Brigade CFDBB Installationsanleitung

Custom PanelBuilt-in Bottom-Freezer RefrigeratorInstallation Guide

Custom Grille Dimensions (Bottom-Freezer)10Reverse dimensions for other end.1/2”(1.27 cm)1-1/2”(3.81 cm)1/4” Radius(.64 cm)2-3/4”(6.98 cm)1/2”(1.27 cm

3 25/32”(9.60 cm)27/32”(.84 cm)9/16”(1.42 cm)1/4”(.635 cm)16.5˚20.0˚Note: This part should be located at the center of the grille. If desired, two per

12Top ViewTop ViewDoor24”(61.0 cm)standard cabinet depth25”(63.5 cm)countertopdepth25”(63.5 cm)countertopdepth25”(63.5 cm)countertopdepthWall3/4”(1.9

133/4”(1.9 cm)End panel1”(2.5 cm)1/4”(0.6 cm)Z-Bracket21-3/4”(55.2 cm)21-3/4”(55.2 cm)24”(61.0 cm)Optional kickplate notch(Dimensions determined by ca

14Custom Panel General InformationCustom finishing options• All installations must allow for the refrigeratorand freezer door to open a minimum of 90˚

157Slide custom wood panel to the hinge side, ensuring “Z” bracket engages the door bracket.8x13x2x2Reinstall handle side door trim and door trim scre

16Open freezer door. Remove door trim screws and door trim with a phillips screwdriver.Remove bracket.1x162Attach bracket to the custom panel. Align a

17Install Door Trim InsertUse the roll of trim insert located in the drawer insidethe unit to apply to the door trim.1Measure and cut 2-1/16” (5.2 cm

1812Remove air grille center blade.Remove two 1/4” (0.6 cm) screws with a magneticextended screwdriver at least 8” (20.3 cm) long.34Pull air grille as

196Insert custom air grille assembly.Install two 1/4” (0.6 cm) screws with a magneticextended screwdriver at least 8” (20.3 cm) long.Install custom ai

2Table of ContentsWarnings & Important Information ____________________________________________________________________3Dimensions and Specificati

20General InformationArea RequirementsVerify the following:• Unit can fit into residence and can be movedaround corners and through doorways.• Floors

21General Information• DO NOT use the self-piercing feature of a saddlevalve. The hole made by the piercing lance is toosmall for the water flow rate

2212Place unit in front of cutout.Pull the center grille louver up at an angle and pull out.34Using an 8” (20.3 cm) magnetic nut driver, remove the tw

23Remove four side screws and remove unit top.Loosen the four hinge screws. Adjust door. Retighten four hinge screws.Replace unit top and four side sc

243”3”3”10aPlace unit within 3” of being flush with cabinets. Note: To avoidcabinet damage, place cardboard between cabinets and unit. Whenmoving unit

25Lift unit off rollers to desired height and level unit using a 5/16” head wrench.Note: DO NOT use an electric device. Overtightening can cause damag

26Align holes on both ends of louvered panels and insert screws.Using a phillips screwdriver, attach the kickplate to the unit and adjust to desired h

27Water Filter System Specification and PerformanceData SheetThis system has been tested according to NSF/ANSI 42/53 for reduction of the substances l

28Replace top air grille.Using an 8” magnetic nut driver, replace the two 1/4” screws.Replace the center grille louver.Open door. The display should f

29Performance Checklist□ Verify cabinet size.□ Verify electrical supply and water supply (if applicable).□ Install anti-tip device(s) and verify unit

3IMPORTANT – Please Read and Follow• Make sure that incoming voltage is the same asunit rating. An electric rating plate specifyingvoltage, frequency,

30Verify OperationsControl Panels1. Press “Activate Controls” pad.2. Verify unit is not in Sabbath Mode.If in Sabbath Mode:A. The Sabbath Mode will di

31If service is required, call your dealer or authorized service agency. The name of the authorizedservice agency can be obtained from the dealer or d

Viking Range, LLC111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-(845-4641)or visit our web site at b

IMPORTANT–Please Read and Follow!4A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/locallaws, or local ordinances.•

Dimensions (Bottom-Freezer)536” Bottom-Freezer51-7/8”(131.8 cm)23-1/16”(58.6 cm)3-19/32”(9.1 cm)82-3/4”(210.2 cm)min.to84-1/16”(213.5 cm)max.Measureme

Specifications (Bottom-Freezer)636” Bottom-FreezerDescription FDBB/CFDBBOverall width 36” (91.5 cm)Overall height (from bottom) 82-3/4” (210.2 cm) min

79”(22.9 cm)73-3/8”(186.4 cm)82-7/8”(210.5 cm) min.anti-tip board &opening height84-1/16”(213.5 cm) max.anti-tip board &opening height36”(91.5

8Anti-Tip Dimensions (Bottom-Freezer)One 2”x 4” mounting board1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)Note: If unit is installed deeper than 24” (61.0 cm), t

35-1/4”(89.5 cm)23-1/16”(58.6 cm)3/4”(1.9 cm)35-1/4”(89.5 cm)32-1/4” to notch(81.9 cm)5/8”(1.6 cm)51-7/8”(131.8 cm)51-1/4”(130.2 cm)3/4”(1.9 cm)Note: